Pepperl+Fuchs FB3205B3

HART Transmitter Power Supply, Input Isolator

3-wire transmitter:Measurement loop: channel I 3+, 4-, channel II 7+, 8-, channel III 11+, 12-, channel IV 15+, 16-Supply circuit: channel I 1+, 2-, channel II 5+, 6-, channel III 9+, 10-, channel IV 13+, 14-4-wire transmitter (powered externally):Measurement loop: channel I 3+, 4-, channel II 7+, 8-, channel III 11+, 12-, channel IV 15+, 16-Supply circuit: channel I 1+, 4-, channel II 5+, 8-, channel III 9+, 12-, channel IV 13+, 16-

Power consumption	2.7 W
Transmitter supply voltage	min. 15 V at 20 mA ; 21.5 V at 4 mA
Connection	backplane bus
Ambient temperature	-20 ... 60 ?°C (-4 ... 140 ?°F)
IECEx approval	IECEx PRE 19.0011U
Connection	removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm2) or screw terminals (0.08 ... 1.5 mm2)
LED indication	Power LED (P) green: supply Diagnostic LED (I) red: module fault , red flashing: communication error , white: fixed parameter set (parameters from com unit are ignored) , white flashing: requests parameters from com unit Status LED (1-4) red: line fault (lead breakage or short circuit)
Relative humidity	EN 60068-2-78:2001
Connection	backplane bus
Dimensions	57 x 107 x 132 mm (2.2 x 4.2 x 5.2 inch)
Supplementary information	EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com.
Electromagnetic compatibility	NE 21:2007
HART secondary variable	no
Environmental test	EN 60068-2-14:2009
Line fault detection	can be switched on/off for each channel via configuration tool , configurable via configuration tool
Conversion time	max. 100 ms
System information	The module has to be mounted in appropriate backplanes and housings (FB92**) in Zone 1, 2, 21, 22 or outside hazardous areas (gas or dust). Here, observe the corresponding EC-type examination certificate.
Damaging gas	EN 60068-2-42:2003
Resolution	12 Bit (0 ... 26 mA)
Shock resistance	EN 60068-2-27:2009
Number of channels	4
Power dissipation	1.5 W
Vibration resistance	EN 60068-2-6:2008
Storage temperature	-25 ... 85 ?°C (-13 ... 185 ?°F)
Input resistance	15 Ω
Degree of protection	IP20 (module) , a separate housing is required acc. to the system description
Interface	manufacturer-specific bus to standard com unit
HART communication	yes
Degree of protection	IEC 60529:2000
Occupied slots	2
Coding	optional mechanical coding via front socket
Mass	approx. 955 g
EU-Type Examination Certificate	Presafe 19 ATEX 14056U
ATEX approval	Presafe 19 ATEX 14056U
Damaging gas	designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3
Shock resistance	shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18
Rated voltage	12 V DC , only in connection with the power supplies FB92**
Vibration resistance	frequency range 10 ... 150 Hz; transition frequency: 57.56 Hz, amplitude/acceleration ?± 0.075 mm/1 g; 10 cycles frequency range 5 ... 100 Hz; transition frequency: 13.2 Hz amplitude/acceleration ?± 1 mm/0.7 g; 90 minutes at each resonance
Relative humidity	95 % non-condensing
Refresh time	100 ms
Connection	2-wire transmitter (HART):

---