Pepperl+Fuchs FB8209H0907
Unicom Com Unit for PROFIBUS DP/DP-V1
- Interface between the I/O modules and the PCS/PLC
- Com unit for 80 analog or 184 digital channels
- Communication via PROFIBUS DP
- Installation in suitable enclosures in Zone 1
- HART communication via PROFIBUS DP V1 or service bus
- Configuration via FDT 1.2 DTM
- Configuration in run (CiR) for any PCS
- Non-volatile memory for configuration and parameter settings
- Self configuration in redundant systems
- Permanently self-monitoring
- Outputs drive to safe state in case of failures
Item Number:
FB8209H0907
The price is not final. Please check with the manager!
Contact our experts
- Overview
- Comments
| Relative humidity | EN 60068-2-56 |
| Environmental test | EN 60068-2-14 |
| LED indication | LED green (power supply): On = operating, fast flash = cold start, slow flash = HCIR loading active LED red (collective alarm): On = internal fault, flashing = no PROFIBUS connection LED yellow (operating mode): flashing 1 (1:1 ratio) = active, normal operation; flashing 2 (7:1 ratio) = active, simulation |
| Number of repeaters between Master and Slave | max. 3 |
| Vibration resistance | EN 60068-2-6 |
| HART communication | via PROFIBUS or service bus |
| System information | The module has to be mounted in appropriate backplanes (FB92**) in Zone 1, 2, or outside hazardous areas. Observe the corresponding EC-type examination certificate. |
| Vibration resistance | frequency range 10 ... 150 Hz; transition frequency: 57.56 Hz, amplitude/acceleration В± 0.075 mm/1 g; 10 cycles frequency range 5 ... 100 Hz; transition frequency: 13.2 Hz amplitude/acceleration В± 1 mm/0.7 g; 90 minutes at each resonance |
| Redundancy | via front connector |
| Damaging gas | designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3 |
| EU-Type Examination Certificate | PTB 97 ATEX 1074 U |
| Storage temperature | -25 ... 85 В°C (-13 ... 185 В°F) |
| Shock resistance | EN 60068-2-27 |
| Degree of protection | IEC 60529 |
| Fieldbus standard | IEC 61158-2 |
| Connection | backplane bus |
| Damaging gas | EN 60068-2-42 |
| Bus length | max. 1000 m (FOL, 1.5 MBaud), max. 1000 m (copper cable, 187.5 kBd), max. 200 m (copper cable, 1.5 MBd) |
| EAC approval | Russia: RU C-IT.MIII06.B.00129 |
| GSE file | CGV61710.gsd/gse |
| Ambient temperature | -20 ... 60 В°C (-4 ... 140 В°F) |
| Power dissipation | 1.8 W |
| Connection | backplane bus |
| Shock resistance | shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18 |
| Number of stations per bus segment | max. 31 (RS-485 standard) |
| Supplementary information | EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com. |
| Addressing | via configuration software |
| Mass | approx. 750 g |
| Supported I/O modules | all FB remote I/O modules |
| Power consumption | 1.8 W |
| Cyclic process data | 240 bytes input and (simultaneously) 240 bytes output |
| Dimensions | 57 x 107 x 132 mm (2.2 x 4.2 x 5.2 inch) |
| Rated voltage | 5 V DC , only in connection with the power supplies FB92** |
| Relative humidity | 95 % non-condensing |
| PROFIBUS address | 0 ... 126 (factory standard setting: 126) |
| Electromagnetic compatibility | NE 21 |
| Fieldbus type | PROFIBUS DP/DP-V1 |
| Degree of protection | IP20 (module) , a separate housing is required acc. to the system description |
| Connection | via backplane |
| Number of stations per bus line | max. 125 (PROFIBUS), max. 119 (service bus) |
| Configuration (240 bytes I/O) | Standard: 80 analog, 184 digital Universal 2I2O: 48 analog, 184 digital Universal 4I4O: 60 analog, 120 digital |
Comments
No comments yet