Pepperl+Fuchs HiDMux2700
HART Multiplexer Master hid mux 2700
- 32-channel
- 24 V DC supply
- HART field device input (revision 5 to 7)
- RS-485 interface
- Up to SIL 3 acc. to IEC 61508
Item Number:
HiDMux2700
The price is not final. Please check with the manager!
Contact our experts
- Overview
- Comments
Mountingon Termination Board
| Relative humidity | 5 ... 95 %, noncondensing |
| Data link type | HART primary and secondary |
| Mass | approx. 140 g |
| Terminating resistor | external 230 ... 500 andOmega; standard (up to 1000 andOmega; possible) |
| Input voltage range | 0.12 ... 1.5 V ss |
| Transmit amplitude | 200 andOmega; load, 0.43 Vpp < signal < 0.49 Vpp 500 andOmega; load, 1.1 Vpp < signal < 1.2 Vpp |
| Address | 1 ... 31 , adjustable via DIP switch |
| Impedance | high impedance |
| Labeling | space for labeling at the front |
| Carrier detect level | signal > 0.12 Vpp, carrier detection activated signal < 0.08 Vpp, carrier detection not activated |
| Signal range | 0.12 Vpp < signal < 1.5 Vpp |
| Interface/power supply | 500 Vrms |
| Common mode clamping | В± 10 V , for transient or AC signals |
| Certificate | CML 17 ATEX 3337 X |
| Supplementary information | Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com. |
| Safety Integrity Level (SIL) | SIL 3 |
| Degree of protection | IEC 60529:2001 |
| Dimensions | 18 x 106 x 128 mm (0.7 x 4.2 x 5 inch) |
| Topology | multi point, master/slave connection |
| Leakage current | < 3 andmicro;A at -20 ... 85 В°C (-4 ... 185 В°F) |
| Power dissipation | 0.7 W at 24 V |
| Rated voltage | 20.4 ... 30 V DC via Termination Board |
| Degree of protection | IP20 |
| Ambient temperature | -20 ... 60 В°C (-4 ... 140 В°F) |
| Type | RS-485 , differential pair and grounding |
| Connection | SL1: 1a, 1b(-); 2a, 2b(+) |
| Rated current | 28 mA at 24 V , RS-485, quiescent current |
| Number of channels | 32 |
| Differential mode clamping | В± 5.2 V , for transient or AC signals |
| Common mode voltage | max. 30 V |
| Transfer rate | 9600 MBit/s, 19200 MBit/s or 38400 MBit/s, selectable via switch |
| Field multi point support | option available upon request |
| DC isolation | dual capacitor each channel |
| Common mode voltage | up to 30 V |
| Display elements | LEDs LED PWR ON (power supply), one green LED LED HART TX (HART transmission), one yellow LED LED FAULT (lead fault), one red LED |
| Output voltage | 400 mV ss (with the terminator resistance specified above) |
| Conformity | HART field device input (revision 5 to 7) |
| Interface/field channels | 1000 Veff |
| Power supply/field channels | 1000 Veff |
| Input impedance | > 5 kandOmega; , according to HART specification |
| Control elements | DIP switches at the housing side for: - unit slave address - baud rate - test mode on/off |
| Device type | DC isolated bus device |
| Output resistance | 100 andOmega; or smaller, capacitive coupling |
| Configuration | via DIP switches |
| Electromagnetic compatibility | NE 21:2012 For further information see system description. |
Comments
No comments yet