Pepperl+Fuchs LB4002A2
HART Output Isolator
- 1-channel
- Analog output module for 0/4 mA ... 20 mA
- Installation in Zone 2 or safe area
- HART communication via field bus or service bus
- Simulation mode for service operations (forcing)
- Line fault detection (LFD)
- Permanently self-monitoring
- Module can be exchanged under voltage
Item Number:
LB4002A2
The price is not final. Please check with the manager!
Contact our experts
- Overview
- Comments
| Connection | channel I: 2/3+, 4/5- |
| Line fault detection | can be switched on/off for each channel via configuration tool , configurable via configuration tool |
| Interface | manufacturer-specific bus to standard com unit |
| Degree of protection | IEC 60529:2000 |
| IECEx approval | BVS 11.0068X |
| Power consumption | 0.95 W |
| Ambient temperature | -20 ... 60 В°C (-4 ... 140 В°F) , 70 В°C (non-Ex) |
| Refresh time | 100 ms |
| Supplementary information | EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com. |
| Number of channels | 1 |
| Damaging gas | EN 60068-2-42:2003 |
| Coding | optional mechanical coding via front socket |
| Load | 750 andOmega; max. |
| Current | 0 ... 25 mA short-circuit protected |
| Mass | approx. 90 g |
| Occupied slots | 1 |
| Relative humidity | 95 % non-condensing |
| Degree of protection | IP20 when mounted on backplane |
| Dimensions | 16 x 100 x 102 mm (0.63 x 3.9 x 4 inch) |
| Rated voltage | 12 V DC , only in connection with the power supplies LB9*** |
| Relative humidity | EN 60068-2-78:2001 |
| Storage temperature | -25 ... 85 В°C (-13 ... 185 В°F) |
| Connection | backplane bus |
| Connection | backplane bus |
| LED indication | Power LED (P) green: supply Diagnostic LED (I) red: module fault , red flashing: communication error , white: fixed parameter set (parameters from com unit are ignored) , white flashing: requests parameters from com unit Status LED (1) red: line fault (lead breakage or short circuit) |
| System information | The module has to be mounted in appropriate backplanes (LB9***) in Zone 2 or outside hazardous areas. Here, observe the corresponding declaration of conformity. For use in hazardous areas (e. g. Zone 2 or Zone 22) the module must be installed in an appropriate enclosure. |
| Watchdog | within 0.5 s the device goes in safe state, e.g. after loss of communication |
| Vibration resistance | EN 60068-2-6:2008 |
| Environmental test | EN 60068-2-14:2009 |
| Certificate | BVS 12 ATEX E 115 X |
| Vibration resistance | frequency range 10 ... 150 Hz; transition frequency: 57.56 Hz, amplitude/acceleration В± 0.075 mm/1 g; 10 cycles frequency range 5 ... 100 Hz; transition frequency: 13.2 Hz amplitude/acceleration В± 1 mm/0.7 g; 90 minutes at each resonance |
| Shock resistance | EN 60068-2-27:2009 |
| Shock resistance | shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18 |
| Connection | removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm2) or screw terminals (0.08 ... 1.5 mm2) |
| HART communication | yes |
| ATEX approval | BVS 12 ATEX E 115 X |
| HART secondary variable | MODBUS: yes; all other bus systems: no |
| Electromagnetic compatibility | NE 21:2007 |
| Power dissipation | 0.8 W |
| Damaging gas | designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3 |
Comments
No comments yet