Pepperl+Fuchs LB6110ER
Digital Output with Shutdown Input
- 4-channel
- Outputs Ex ia
- Installation in Zone 2 or safe area
- Line fault detection (LFD)
- Positive or negative logic selectable
- Simulation mode for service operations (forcing)
- Permanently self-monitoring
- Output with watchdog
- Output with bus-independent safety shutdown
Item Number:
LB6110ER
The price is not final. Please check with the manager!
Contact our experts
- Overview
- Comments
| Reaction time | 10 s |
| Internal resistor | max. 370 Ω |
| Electromagnetic compatibility | NE 21 |
| Dimensions | 32.5 x 100 x 102 mm (1.28 x 3.9 x 4 inch) |
| Response time | 10 ms (depending on bus cycle time) |
| Relative humidity | EN 60068-2-56 |
| Watchdog | within 0.5 s the device goes in safe state, e.g. after loss of communication |
| Interface | manufacturer-specific bus to standard com unit |
| Degree of protection | IEC 60529 |
| System information | The module has to be mounted in appropriate backplanes (LB9***) in Zone 2 or outside hazardous areas. Here, observe the corresponding declaration of conformity. For use in hazardous areas (e. g. Zone 2, Zone 22 or Div. 2) the module must be installed in an appropriate enclosure. |
| Environmental test | EN 60068-2-14 |
| Coding | optional mechanical coding via front socket |
| Open loop voltage | 24.5 V |
| Connection | removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm2) or screw terminals (0.08 ... 1.5 mm2) |
| Input voltage range | 18.5 ... 32 V DC (SELV/PELV) booster voltage |
| Occupied slots | 2 |
| Current limit | 37 mA |
| EU-type examination certificate | PTB 03 ATEX 2042 X |
| Connection | backplane bus |
| Storage temperature | -25 ... 85 В°C (-13 ... 185 В°F) |
| Vibration resistance | EN 60068-2-6 |
| Supplementary information | EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com. |
| LED indication | Power LED (P) green: supply Status LED (I) red: line fault , red flashing: communication error |
| Vibration resistance | frequency range 10 ... 150 Hz; transition frequency: 57.56 Hz, amplitude/acceleration В± 0.075 mm/1 g; 10 cycles frequency range 5 ... 100 Hz; transition frequency: 13.2 Hz amplitude/acceleration В± 1 mm/0.7 g; 90 minutes at each resonance |
| Certificate | PF 08 CERT 1234 X |
| Rated voltage | 12 V DC , only in connection with the power supplies LB9*** |
| Safety Integrity Level (SIL) | SIL 2 |
| Ambient temperature | -20 ... 60 В°C (-4 ... 140 В°F) |
| IECEx approval | BVS 09.0037X |
| Shock resistance | EN 60068-2-27 |
| Connection | backplane bus / booster terminals |
| Damaging gas | EN 60068-2-42 |
| Number of channels | 4 |
| Damaging gas | designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3 |
| Line fault detection | can be switched on/off for each channel via configuration tool also when turned off (every 2.5 s the valve is turned on for 2 ms) |
| Relative humidity | 95 % non-condensing |
| Power dissipation | 3 W |
| ATEX approval | PTB 03 ATEX 2042 X |
| Degree of protection | IP20 when mounted on backplane |
| Connection | channel I: 1+, 2-; channel II: 3+, 4-; channel III: 5+, 6-; channel IV: 7+, 8- |
| Mass | approx. 150 g |
| Power consumption | 0.15 W |
| Shock resistance | shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18 |
Comments
No comments yet