Pepperl+Fuchs LB6115AR
Digital Output
- 4-channel
- Outputs Ex ia
- Installation in Zone 2 or safe area
- Line fault detection (LFD)
- Positive or negative logic selectable
- Simulation mode for service operations (forcing)
- Permanently self-monitoring
- Output with watchdog
Item Number:
LB6115AR
The price is not final. Please check with the manager!
Contact our experts
- Overview
- Comments
| Open loop voltage | 16.6 V |
| Number of channels | 4 |
| Storage temperature | -25 ... 85 В°C (-13 ... 185 В°F) |
| Power dissipation | 3 W |
| Electromagnetic compatibility | NE 21 |
| ATEX approval | PTB 03 ATEX 2042 X |
| LED indication | Power LED (P) green: supply Status LED (I) red: line fault , red flashing: communication error |
| Supplementary information | EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com. |
| EU-type examination certificate | PTB 03 ATEX 2042 X |
| Internal resistor | max. 90 Ω |
| Line fault detection | can be switched on/off for each channel via configuration tool also when turned off (every 2.5 s the valve is turned on for 2 ms) |
| Connection | channel I: 1+, 2-; channel II: 3+, 4-; channel III: 5+, 6-; channel IV: 7+, 8- |
| Degree of protection | IP20 when mounted on backplane |
| Watchdog | within 0.5 s the device goes in safe state, e.g. after loss of communication |
| IECEx approval | BVS 09.0037X |
| Ambient temperature | -20 ... 60 В°C (-4 ... 140 В°F) |
| Occupied slots | 2 |
| Coding | optional mechanical coding via front socket |
| Relative humidity | 95 % non-condensing |
| Rated voltage | 12 V DC , only in connection with the power supplies LB9*** |
| Shock resistance | shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18 |
| Power consumption | 0.15 W |
| Connection | backplane bus / booster terminals |
| Reaction time | 10 s |
| Interface | manufacturer-specific bus to standard com unit |
| Mass | approx. 150 g |
| Damaging gas | designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3 |
| Environmental test | EN 60068-2-14 |
| System information | The module has to be mounted in appropriate backplanes (LB9***) in Zone 2 or outside hazardous areas. Here, observe the corresponding declaration of conformity. For use in hazardous areas (e. g. Zone 2, Zone 22 or Div. 2) the module must be installed in an appropriate enclosure. |
| Dimensions | 32.5 x 100 x 102 mm (1.28 x 3.9 x 4 inch) |
| Relative humidity | EN 60068-2-56 |
| Connection | removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm2) or screw terminals (0.08 ... 1.5 mm2) |
| Input voltage range | 18.5 ... 32 V DC (SELV/PELV) booster voltage |
| Vibration resistance | EN 60068-2-6 |
| Shock resistance | EN 60068-2-27 |
| Current limit | 70 mA |
| Response time | 10 ms (depending on bus cycle time) |
| Connection | backplane bus |
| Certificate | PF 08 CERT 1234 X |
| Degree of protection | IEC 60529 |
| Vibration resistance | frequency range 10 ... 150 Hz; transition frequency: 57.56 Hz, amplitude/acceleration В± 0.075 mm/1 g; 10 cycles frequency range 5 ... 100 Hz; transition frequency: 13.2 Hz amplitude/acceleration В± 1 mm/0.7 g; 90 minutes at each resonance |
| Damaging gas | EN 60068-2-42 |
Comments
No comments yet