Pepperl+Fuchs LB6116E
Digital Output with Shutdown Input
- 2-channel
- Outputs Ex ia
- Mounting in Zone 2, Class I/Div.2 or in the safe area
- Line fault detection switched on and off
- Positive or negative logic selectable
- Simulation mode for service operations (forcing)
- Permanently self-monitoring
- Output with watchdog
- Output with bus-independent safety shutdown
- Module can be exchanged under voltage (hot swap)
Item Number:
LB6116E
The price is not final. Please check with the manager!
Contact our experts
- Overview
- Comments
| Damaging gas | designed for operation in environmental conditions acc. to ISA-S71.04-1985, severity level G3 |
| Watchdog | within 0.5 s the device goes in safe state, e.g. after loss of communication |
| Environmental test | EN 60068-2-14 |
| Vibration resistance | EN 60068-2-6 |
| Power dissipation | 1.95 W |
| Line fault detection | can be switched on/off for each channel via configuration tool also when turned off (every 2.5 s the valve is turned on for 2 ms) |
| Power consumption | 2.9 W |
| Shock resistance | EN 60068-2-27 |
| Mass | approx. 150 g |
| Vibration resistance | frequency range 10 ... 150 Hz; transition frequency: 57.56 Hz, amplitude/acceleration В± 0.075 mm/1 g; 10 cycles frequency range 5 ... 100 Hz; transition frequency: 13.2 Hz amplitude/acceleration В± 1 mm/0.7 g; 90 minutes at each resonance |
| Connection | backplane bus |
| Connection | channel I: 1+, 4/5/6/8-; channel II: 7+, 4/5/6/8- |
| Supplementary information | Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com. |
| Storage temperature | -25 ... 85 В°C (-13 ... 185 В°F) |
| EU-type examination certificate | EXA 16 ATEX 0025X |
| Connection | removable front connector with screw flange (accessory) wiring connection via spring terminals (0.14 ... 1.5 mm2) or screw terminals (0.08 ... 1.5 mm2) |
| Rated voltage | Use only in connection with the power supplies LB9*** |
| Relative humidity | 95 % non-condensing |
| Dimensions | 16 x 100 x 102 mm (0.63 x 3.9 x 4 inch) |
| Response time | 10 ms (depending on bus cycle time) |
| Damaging gas | EN 60068-2-42 |
| Electromagnetic compatibility | NE 21 |
| Degree of protection | IP20 when mounted on backplane |
| LED indication | Power LED (P) green: supply Diagnostic LED (I) red: module fault , red flashing: communication error , white: fixed parameter set (parameters from com unit are ignored) , white flashing: requests parameters from com unit Status LED (1, 2) red: line fault (lead breakage or short circuit) , yellow: state of digital I/O (0/1) Mode LED (M) white: Parallel operation of outputs |
| Degree of protection | IEC 60529 |
| Occupied slots | 1 |
| Relative humidity | EN 60068-2-56 |
| Number of channels | 2 |
| Connection | backplane bus |
| Coding | optional mechanical coding via front socket |
| Open loop voltage | 23 V , both channels parallel 23 V |
| Current limit | 40 mA both channels parallel 80 mA |
| System information | The module has to be mounted in appropriate backplanes (LB9***) in Zone 2 or outside hazardous areas. Here, observe the corresponding declaration of conformity. For use in hazardous areas (e. g. Zone 2, Zone 22 or Div. 2) the module must be installed in an appropriate enclosure. |
| Interface | manufacturer-specific bus to standard com unit |
| Internal resistor | 258 Ω , both channels parallel 129 Ω |
| Ambient temperature | -20 ... 60 В°C (-4 ... 140 В°F) |
| Shock resistance | shock type I, shock duration 11 ms, shock amplitude 15 g, number of shocks 18 |
| ATEX approval | EXA 16 ATEX 0025X |
Comments
No comments yet