Pepperl+Fuchs LD28/LV28-Z-F1/47/76a/82b/116
Thru-beam sensor
- Universal series with highly versatile fields of use
- Resistant against noise: reliable operation under all conditions
- Highly visible LED as alignment aid in receiver optics
- Programmable time function GAN, GAB, IAB as well as GAN-IAB and GAN-GAB as double function
- Emitter with test input
- Version with red light
- Overview
- Comments
| Ambient temperature | -40 ... 60 В°C (-40 ... 140 В°F) |
| Housing width | 25.8 mm |
| Switching current | max. 200 mA |
| Function indicator | LED yellow: 1. LED lit constantly: signal > 2 x switching point (function reserve) 2. LED flashes: signal between 1 x switching point and 2 x switching point 3. LED off: signal < switching point |
| Protection class | II, rated insulation voltage 250 V AC with pollution degree 1-2 according to IEC 60664-1 Output circuit basis insulation of input circuit according to EN 50178, rated insulation voltage 250 V AC Caution! The protection class 2 is only valid when the terminal compartment is closed. |
| Light type | modulated visible red light , 660 nm |
| Threshold detection range | 40 m |
| Signal output | 2 PNP, complementary, short-circuit protected, reverse polarity protected , open collectors |
| Test input | emitter deactivation at +UB (Imax. < 3 mA at 30 V DC) |
| Angle of divergence | Emitter 1.2В°, Receiver 5В° |
| Diameter of the light spot | approx. 0.6 m at 30 m |
| No-load supply current | Emitter: 50 mA Receiver: 35 mA |
| Ripple | 10 % |
| UL approval | cULus Listed , Class 2 power source |
| Storage temperature | -40 ... 75 В°C (-40 ... 167 В°F) |
| Control elements | sensitivity adjustment (Adjustment to < 25% of the effective operating range) , Light-on/dark-on changeover switch |
| Housing height | 88 mm |
| Effective detection range | 0 ... 30 m |
| Alignment aid | LED red (in receiver lens) illuminated constantly: beam is interrupted, flashes: reaching switching point, off: sufficient stability control |
| Connection | terminal compartment with 8 spring-loaded terminals for wire cross section 0.5 ... 1.5 mm2 , Insulation stripping 7.5 ... 8.5 mm , M16 x 1.5 cable gland |
| Response time | 0.5 ms |
| CCC approval | CCC approval / marking not required for products rated 36 V |
| Light source | LED |
| Emitter | LD28-F1/76a/116 |
| Product standard | EN 60947-5-2 |
| Operation indicator | LED green |
| Pre-fault indication output | 1 PNP transistor, short-circuit protected, protected from reverse polarity, open collector, Umax = 30 V DC, Imax = 0.2 A The output becomes inactive if the signal level has fallen below the function reserve for approx. 10 s (yellow and red LEDs flash). If the light beam is interrupted four times during this period, the output immediately becomes inactive. |
| Transmitter frequency | F1 = 25 kHz |
| Mission Time (TM) | 20 a |
| Degree of protection | IP67 |
| MTTFd | 620 a |
| Timer function | ON delay (GAN), OFF delay (GAB), one shot (IAB), ON delay-one shot (GAN-IAB), ON delay-OFF delay (GAN-GAB), programmable adjustment interval 0.02 s ... 1 s |
| Switching frequency | 1000 Hz |
| Switching voltage | max. 30 V DC |
| Mass | 200 g (emitter and receiver) |
| Operating voltage | 10 ... 30 V DC |
| Ambient light limit | 50000 Lux |
| Switching type | light/dark on, switchable |
| Housing depth | 65.5 mm |
| Receiver | LV28-Z-F1/47/82b/116 |
| Diagnostic Coverage (DC) | 90 % |
Comments
No comments yet