Pepperl+Fuchs NBN3-F31K2M-Z8L-B13-S-3G-3D
Inductive sensor
- Direct mounting on standard actuators
- ATEX-approval for zone 2 and zone 22
- Compatible with all process control systems
- 2-wire DC sensor with minimum off-state current
- Rugged metal base
- Weatherproof housing for outdoor applications
- Plug-in terminals
Item Number:
NBN3-F31K2M-Z8L-B13-S-3G-3D
The price is not final. Please check with the manager!
Contact our experts
- Overview
- Comments
| Assured operating distance | 0 ... 2.05 mm |
| Ambient temperature | -40 ... 75 В°C (-40 ... 167 В°F) , restriction for use in hazardous area, see instruction manual |
| Housing material | rugged polycarbonate (PC) + GF 10% , optimised for outdoor use |
| Diagnostic Coverage (DC) | 0 % |
| Off-state current | 100 ... 200 andmicro;A typ. 160 andmicro;A |
| Reverse polarity protection | reverse polarity tolerant |
| Operating current | 4 ... 100 mA |
| Operating voltage | 6 ... 30 V |
| ATEX marking | The Ex-related marking can also be printed on the enclosed label. |
| Tightening torque, housing screws | 1.5 Nm |
| Connection (valve side) | screw terminal , Cable gland M20 x 1.5 |
| Mission Time (TM) | 20 a |
| Output polarity | DC |
| Rated operating distance | 2.5 mm |
| Voltage drop | 6 V |
| MTTFd | 684 a |
| Degree of protection | IP67 ; additional degree of protection IP66/IP69 with BT65-F31K2-RG-EN-01 and SH-F31K2-B13 |
| Storage temperature | -40 ... 85 В°C (-40 ... 185 В°F) |
| Tightening torque, earthing screw | 1.5 Nm |
| Short-circuit protection | no |
| Current | max. 240 mA |
| Use in the hazardous area | see instruction manuals |
| Switching frequency | 0 ... 100 Hz |
| Housing base | powder coated aluminum |
| Standards | EN 60079-0:2012+A11:2013, EN 60079-31:2014 Protection by enclosure ""tc"" Some of the information in this instruction manual is more specific than the information provided in the datasheet. |
| ATEX marking | The Ex-related marking can also be printed on the enclosed label. |
| Short-circuit protection | no |
| CE marking | [*PD-Z02586A*] |
| Connection (system side) | M20 x 1.5 cable gland , ground connection with earthing screw only for wire cross-section 4 mm2, use solid wire or stranded wire with wire end ferrule |
| Tightening torque, cable gland | max. 4 Nm |
| Certificate | PF 15CERT3754 X |
| Switching function | 2 x normally open (NO) |
| Standards | EN 60079-0:2012+A11:2013, EN 60079-15:2010 Ignition protection category ""n"" Use is restricted to the following stated conditions |
| Output type | 2x 2-wire |
| Tightening torque, fastening screws | 2 Nm |
| Output type | Two-wire |
| CE marking | [*PD-Z02586A*] |
| Reverse polarity protection | yes, with reversed output LED is out of function, therfore more power for solenoid valve |
| Tightening torque, stopping plug | 2 Nm |
| Hysteresis | typ. 0.5 mm |
| Installation | for non-flush mounting |
| Voltage | max. 32 V DC |
| General | The corresponding datasheets, declarations of conformity, EU type examination certificates, certificates, and control drawings, where applicable (see datasheets), form an integral part of this document. These documents are available at www.pepperl-fuchs.com. The maximum surface temperature of the device was determined without a layer of dust on the apparatus. Some of the information in this instruction manual is more specific than the information provided in the datasheet. |
Comments
No comments yet