Pepperl+Fuchs PMI40-F90-IU2EP-IO-V15-3G-3D
Inductive positioning system
- Parameterization and diagnosis via IO-Link
- Measuring range 0 ... 40 mm
- Parameterisable measuring range
- Analog current or voltage output, programmable
- 2 Push-pull outputs
- Switch points programmable via IO-Link
- Overview
- Comments
| Use in the hazardous area | see instruction manuals |
| Possible characteristics | maximum operating voltage UBmax , maximum load current ILmax , minimum series resistance RV , maximum analog output voltage UAmax , maximum analog output current IAmax |
| Measurement range | 0 ... 40 mm |
| Operating voltage indicator | LED green |
| Linearity error | within measuring range: В± 0.8 mm within linearity range: В± 0.4 mm |
| SIO mode support | yes |
| LED S3 | Damping element in the configured analog measuring range |
| Load resistor | current output: 400 andOmega; voltage output: 1000 andOmega; |
| Short-circuit protection | pulsing |
| MTTFd | 382 a |
| IO-Link Revision | 1.1 |
| Operating voltage | 12 ... 30 V DC (13 ... 30 V when analog voltage output is parameterized) |
| Device ID | 0x200204 (2097668) |
| Diagnostic Coverage (DC) | 0 % |
| Process data witdh | Process data input: 16 Bit Process data output: none |
| Device profile | Smart Sensor |
| Connection type | 5-pin, M12 x 1 connector |
| LED STATUS | Status display LED, green/red (Power on, communication/error, missing damping element) |
| Mass | 56 g |
| Interface type | IO-Link (via C/Q = Pin 4) |
| Mission Time (TM) | 20 a |
| Temperature drift | В± 0.5 mm (-25 В°C ... 70 В°C) |
| LED S1 | switching state Switching output 1 |
| Operating current | 100 mA / output |
| Value range | 0000h ... 3200h |
| Maximum permissible ambient temperature | Also observe the maximum permissible ambient temperature stated in the general technical data. Keep to the lower of the two values. mode of operation 1 at UBmax = 30 V and maximum 2 switching outputs with each ILmax =100 mA and 1 analog output with IAmax = 20mA or UAmax = 10 V : 30 В°C (86 В°F) mode of operation 2 at UBmax = 30 V and maximum 1 switching output with ILmax =100 mA : 50 В°C (122 В°F) |
| Output type | 1 current output: 4 ... 20 mA or 1 voltage output: 0 ... 10 V , programmable |
| Short-circuit protection | voltage output: current limit |
| Type of protection | Protection by enclosure ""tc"" |
| Resolution | 50 andmicro;m |
| Reverse polarity protection | reverse polarity protected |
| Switching hysteresis | 0.2 mm |
| Output type | 2 push-pull outputs (can be parameterized), short-circuit-proof, reverse polarity protection, surge-proof |
| Compatible master port type | A |
| Switching element function | Analog current or voltage output, programmable 2 switch outputs, programmable |
| CE marking | [*PD-Z02586A*] |
| Possible characteristics | maximum operating voltage UBmax , maximum load current ILmax , minimum series resistance RV , maximum analog output voltage UAmax , maximum analog output current IAmax |
| Type of protection | ""n"" |
| Transfer rate | COM 2 (38.4 kBaud) |
| Equipment protection level | Gc (nA) , Dc |
| CE marking | [*PD-Z02586A*] |
| LED S2 | switching state Switching output 2 |
| Degree of protection | IP67 / IP69K |
| UL approval | cULus Listed, Class 2 Power Source, Type 1 enclosure |
| Ambient temperature | -25 ... 85 В°C (-13 ... 185 В°F) |
| Voltage drop | 3 V |
| Object distance | 0.5 ... 3 mm , recommended: 1.5 mm |
| Repeat accuracy | В± 0.1 mm |
| Maximum permissible ambient temperature | Also observe the maximum permissible ambient temperature stated in the general technical data. Keep to the lower of the two values. mode of operation 1 at UBmax = 30 V and maximum 2 switching outputs with each ILmax =100 mA and 1 analog output with IAmax = 20mA or UAmax = 10 V : 30 В°C (86 В°F) mode of operation 2 at UBmax = 30 V and maximum 1 switching output with ILmax =100 mA : 50 В°C (122 В°F) |
| Linearity range | 1 ... 39 mm |
| Min. cycle time | 2.3 ms |
| Switching window | В± 1 mm |
| No-load supply current | 40 mA |
Comments
No comments yet