Pepperl+Fuchs VBA-2A-KE5-IL/UL
AS-Interface analog module
- Housing with push-in connection technology and mechanically coded terminal blocks
- Housing width 19 mm, installation in the switch cabinet on DIN mounting rail
- Power supply of outputs from the external auxiliary voltage
- Function display for bus, external auxiliary voltage and outputs
Item Number:
VBA-2A-KE5-IL/UL
The price is not final. Please check with the manager!
Contact our experts
- Overview
- Comments
| Temperature influence | 1 andmicro;A/K or 0,3 mV/K |
| LED AUX | ext. auxiliary voltage UAUX; dual LED green/red green: voltage OK red: reverse voltage |
| Data bits (function via AS-Interface) | The transfer of the data value is based on AS-Interface Profile 7.3. |
| LED OUT | Status of output signal; yellow LED Yellow: output value within value range Continually on: current mode 1.4 s on/0.1 s off: voltage mode Flashing yellow: wire break (at current output) or output value outside of value range |
| Altitude | 2000 m above MSL |
| Vibration resistance | 0.35 mm 10 ... 57 Hz , 5 g 57 ... 150 Hz, 20 cycles |
| Short-circuit current | voltage output: max. 22 mA |
| AS-Interface specification | V3.0 |
| Protection class | III |
| Relative humidity | 85 % , noncondensing |
| Parameter bits (programmable via AS-i) | function |
| ID1 code | F |
| Auxiliary voltage (output) | 24 V DC В± 15 % PELV |
| Ambient temperature | -25 ... 70 В°C (-13 ... 158 В°F) |
| Current consumption | IAUX 650 mA |
| Load | voltage output: min. 1 kandOmega; current output: max. 600 andOmega; |
| Resolution | Voltage output: 3 mV Current output: 6 andmicro;A |
| Noise immunity | EN 61000-6-2:2005, EN 61326-1:2006, EN 62026-2:2013 |
| Number/Type | Two analog outputs Current: 0 mA ... 20 mA Voltage: 0 V ... 10 V |
| Pollution degree | 2 |
| AS-Interface | EN 62026-2:2013 |
| LED FAULT | Fault indication: red LED Red: communication error or address is 0 Red flashing: peripheral fault |
| Degree of protection | IP20 |
| Slave type | Standard slave |
| MTBF | 197 a |
| Emitted interference | EN 61000-6-4:2007 |
| UL File Number | E223772 |
| Profile | S-7.3.5 |
| Connection | Removable push-in terminals rated connection capacity: rigid: 0.20 mm2 ... 1.5 mm2 flexible (without wire end ferrule): 0.20 mm2 ... 2.5 mm2 flexible (with wire end ferrule): 0.25 mm2 ... 1.5 mm2 |
| Current loading capacity | 600 mA (signal current + actuator power supply) from external auxiliary voltage UAUX, overload-proof and short-circuit proof |
| Mass | 110 g |
| Required master specification | V2.1 |
| Rated operating current | 75 mA |
| Supply | From auxiliary voltage UAUX |
| Climatic conditions | For indoor use only |
| Shock and impact resistance | 15 g, 11 ms in 6 spatial directions, 3 shocks 10 g, 16 ms in 6 spatial directions, 1000 shocks |
| LED PWR | AS-Interface voltage; green LED Green: voltage OK Flashing green: address 0 or peripheral error |
| Rated operating voltage | 26.5 ... 31.6 V from AS-Interface |
| Surge protection | UAUX, Ue: overvoltage category II, safe isolated power supplies (PELV) |
| Fieldbus standard | EN 62026-2:2013 |
| IO code | 7 |
| Storage temperature | -25 ... 85 В°C (-13 ... 185 В°F) |
| ID2 code | 5 |
| ID code | 3 |
| Note | Max. length of jumpers = 5 cm |
| Mounting | DIN mounting rail |
| Degree of protection | EN 60529:2000 |
| Accuracy | 0.15 % of full-scale value |
Comments
No comments yet