Pepperl+Fuchs VBA-2E-G11-I/U/PT100-V1
AS-Interface analog module
- Function display for bus, internal and external sensor power supply, inputs
- Supply for inputs from AS-Interface or auxiliary voltage
- Degree of protection IP68 / IP69K
- Accuracy В± 0.1 %
- Channel-specific input monitoring
- Inputs for current, voltage or Pt100 temperature sensor
- Overview
- Comments
| IO code | 7 |
| Storage temperature | -25 ... 85 В°C (-13 ... 185 В°F) |
| ID code | 3 |
| Connection | AS-Interface/UAUX: M12 round connector Inputs: M12 round connector |
| Degree of protection | EN 60529:2000 |
| Mission Time (TM) | 20 a |
| Tightening torque, housing screws | 1.8 Nm |
| ID1 code | F |
| Required master specification | V2.1 |
| Protection class | III |
| AS-Interface specification | V3.0 |
| Fieldbus standard | EN 62026-2:2013 |
| Pollution degree | 3 |
| Rated operating current | 60 mA (without sensors) / max. 200 mA |
| Supply | from AS-Interface (switch position INT, default settings) or auxiliary voltage UEXT (switch position EXT) |
| Auxiliary voltage (output) | 20 ... 30 V DC PELV |
| LED AS-i/FAULT | Status display; multi-colour LED Green: normal operation Red: communication fault Flashing yellow/red: address 0 Flashing green/red: peripheral fault |
| Measuring current | for Pt100: approx. 1 mA |
| Surge protection | UAUX, Uin: Over voltage category III, safe isolated power supplies (PELV) |
| Rated operating voltage | 26.5 ... 31.6 V from AS-Interface |
| Parameter bits (programmable via AS-i) | function |
| Mass | 200 g |
| Data bits (function via AS-Interface) | The transfer of the data value is based on AS-Interface Profile 7.3. |
| Climatic conditions | For indoor use only |
| UL File Number | E223772 |
| LED ANALOG | status of input signal; LED yellow off: not active on: signal within measurement range flashing: signal outside of measurement range |
| Tightening torque, cable gland | 0.4 Nm |
| Temperature influence | Voltage/current: 20 ppm/K Pt100: (10 ppm of indicated temperature [В°C] + 0.003 В°C)/K |
| Current loading capacity | 140 mA from AS-Interface; overload and short-circuit resistant 600 mA from external auxiliary voltage UAUX , overload and short-circuit protected |
| Number/Type | 2 analog inputs Current: 0 ... 20 mA/4 ... 20 mA voltage: 0 ... 10 V Pt100: -200 ... 850 В°C |
| MTTFd | 190 a |
| Altitude | 2000 m above MSL |
| Relative humidity | 85 % , noncondensing |
| Accuracy | Voltage/current: 0.1% of accumulated value Pt100: 0.1% of indicated temperature [В°C] + 0.3 В°C |
| LED AUX | ext. auxiliary voltage UAUX; dual LED green/red green: voltage OK red: reverse voltage |
| LED INT/EXT | status display input supply; LED green green: input supply from AS-Interface off: input supply from auxiliary voltage |
| Slave type | Standard slave |
| Resolution | 16 Bit / 1 andmicro;A (current input) or 16 bit / 1 mV (voltage input) or 16 Bit / 0.1В°C (temperature input) |
| Input resistance | current input: max. 70 andOmega; voltage input: 100 kandOmega; |
| Degree of protection | IP68 / IP69K |
| Profile | S-7.3.D |
| Ambient temperature | -25 ... 70 В°C (-13 ... 158 В°F) |
| Emitted interference | EN 61000-6-4:2007 |
| AS-Interface | EN 62026-2:2013 |
| Noise immunity | EN 61000-6-2:2005, EN 61326-1:2006, EN 62026-2:2013 |
| Input | EN 61131-2:2007 |
| Diagnostic Coverage (DC) | 0 % |
| Mounting | Mounting plate |
| ID2 code | D |
Comments
No comments yet