Pepperl+Fuchs VBA-4E3A-G20-ZEL/M1L-P6
AS-Interface I/O module
- A/B slave with extended addressing possibility for up to 62 slaves
- Inputs for 3-wire sensors
- Outputs for DC roller motors (drum motors)
- Connection of motors and sensors via M8 connectors
- Configurable start/stop ramps
- Communication monitoring
- Power supply of the inputs and outputs from the external auxiliary voltage
- Function display for bus, external auxiliary voltage, in- and outputs
- Cable piercing method with gold plated contact pins
Item Number:
VBA-4E3A-G20-ZEL/M1L-P6
The price is not final. Please check with the manager!
Contact our experts
- Overview
- Comments
| Emitted interference | EN 61000-6-4:2007 |
| Number/Type | 2 Inputs for 3-wire sensors (PNP), DC |
| LED FUSE | Motor power supply; 2 green LEDs |
| LED AUX | ext. auxiliary voltage UAUX; dual LED green/red green: voltage OK red: reverse voltage |
| LED ERR | Motor fault: 2 LED yellow |
| Rated operating current | 35 mA |
| LED PWR | AS-Interface voltage; green LED green: voltage OK green flashing: address 0 or sensor supply overload or speed signal overload or external auxiliary voltage UAUX missing |
| Number/Type | 2 outputs for DC roller motors (MOT1, MOT2) |
| ID1 code | 6 |
| ID code | A |
| UL File Number | E223772 ""For use in NFPA 79 Applications only"" |
| Mass | 220 g |
| Compatible roller motors | Interroll EC310, Rulmeca BL3 |
| Input current | 8 mA (limited internally) |
| MTBF | 98 a |
| Motor fault | Digital input NPN, U0 = 3.3 V, Ri = 52 kandOmega; 0 (no error) 40 andmicro;A 1 (error) 30 andmicro;A |
| Fieldbus standard | EN 62026-2:2013 |
| Input | EN 61131-2:2007 |
| LED FAULT | error display; LED red red: communication error or address is 0 red flashing: overload of sensor supply or speed signal overload or external auxiliary voltage UAUX missing |
| Current loading capacity | 500 mA , overload and short-circuit protected |
| Mounting | 2 clips with andempty; 8 mm drill hole |
| Current | max. 5 A per motor |
| Rated operating voltage | 26.5 ... 31.6 V from AS-Interface |
| Velocity signal | 1.4 andhellip; 13 V at no-load Ri = 5.6 kandOmega;, RLOAD 35 kandOmega; Control via parameter P2:0 |
| Noise immunity | EN 61000-6-2:2005, EN 61326-1:2006, EN 62026-2:2013 |
| LED DIR | Motor rotation direction; yellow LED |
| Profile | S-7.A.E |
| Degree of protection | IP54 according to EN 60529 |
| Supply | from external auxiliary voltage UAUX |
| Auxiliary voltage (output) | 18 ... 30 VDC PELV |
| Input filter | 2 ms |
| Supply | from external auxiliary voltage UAUX |
| ID2 code | E |
| IO code | 7 |
| Data bits (function via AS-Interface) | |
| Note | The flat cable routing is designed for 100 actuation cycles |
| Cable length | 0.35 m |
| Ambient temperature | -25 ... 60 В°C (-13 ... 140 В°F) |
| Signal delay | < 1 ms (input/AS-Interface) |
| Rotation direction signal | Off / (UAUX - 1.0 V) at no-load Ri = 5.6 kandOmega;, RLOAD 5 kandOmega; AS-Interface data bit D2 = 0: UD = Off |
| Overload protection | fuse , I2t = 5.56 A2s |
| Slave type | A/B slave |
| Storage temperature | -25 ... 85 В°C (-13 ... 185 В°F) |
| AS-Interface | EN 62026-2:2013 |
| LED MOT | Motor active; 2 yellow LEDs |
| Switching point | according to DIN EN 61131-2 0 (undamped) 0.5 mA 1 (damped) 2.0 mA |
| Connection | AS-Interface, AUX: Insulation piercing technology Yellow flat cable/black flat cable Inputs/outputs: M8 round plug connector in accordance with EN 61076-2-104 Inputs: LF004-GS1-A (4-pin, bushing contacts, screw lock, A-coded) Matching connector: LM004-Gx1-A or similar Outputs: NF005-SS1-B (5-pin, bushing contacts, snap lock, B-coded). Matching connector: NM005-Sx1-B or similar |
| AS-Interface specification | V3.0 |
| LED IN | switching state (input); 2 LED yellow |
| Required master specification | V2.1 |
| Degree of protection | EN 60529:2000 |
Comments
No comments yet