Pepperl+Fuchs VBA-4E4A-G16-ZEJ/E2L
AS-Interface sensor/actuator module
- Compact design
- Connections via round connector
- AS-Interface connection via M12 metal threaded insert with SPEEDCON
- Function display for bus, ext. auxiliary voltage, inputs and outputs
- Degree of protection IP67 / IP68 / IP69K
- Inputs for 2- and 3-wire sensors
- Supply for inputs from AS-Interface
- Power supply of outputs from the external auxiliary voltage
- Communication monitoring
- Detection of overload on sensor supply
- Detection of output overload with LED per channel
Item Number:
VBA-4E4A-G16-ZEJ/E2L
The price is not final. Please check with the manager!
Contact our experts
- Overview
- Comments
| ID code | A |
| Rated operating voltage | 26.5 ... 31.6 V from AS-Interface |
| Current loading capacity | 200 mA (TB 40 В°C), 150 mA (TB 70 В°C), overload-proof and short-circuit protected |
| Voltage | (UAUX - 0.5 V) |
| Climatic conditions | For indoor use only |
| Emitted interference | EN 61000-6-4:2007 |
| Mission Time (TM) | 20 a |
| Input | EN 61131-2 |
| MTTFd | 190 a |
| LED AUX | ext. auxiliary voltage UAUX; dual LED green/red green: voltage OK red: reverse voltage |
| Auxiliary voltage (output) | 20 ... 30 V DC PELV |
| Degree of protection | EN 60529:2000 |
| Pollution degree | 3 |
| Surge protection | UAUX, Uin: Over voltage category III, safe isolated power supplies (PELV) |
| LED IN | switching state (input); 4 LED yellow |
| Shock and impact resistance | 30 g, 11 ms in 6 spatial directions 3 shocks 10 g, 16 ms in 6 spatial directions 1000 shocks |
| Data bits (function via AS-Interface) | |
| Supply | from external auxiliary voltage UAUX |
| LED OUT | Switching status (output); 4 yellow/red LEDs Yellow: output active Red: output overload |
| Vibration resistance | 0.75 mm 10 ... 57 Hz , 5 g 57 ... 150 Hz, 20 cycles |
| UL File Number | E223772 |
| IO code | 7 |
| ID1 code | 7 |
| Slave type | A/B slave |
| Signal delay | < 1 ms (input/AS-Interface) |
| Tightening torque, cable gland | 0.4 Nm (M12 connector), 0.2 Nm (M8 connector) |
| Fieldbus standard | EN 62026-2:2013 |
| Mounting | screw mounting |
| Noise immunity | EN 61000-6-2:2005 EN 62026-2:2013 |
| Usage category | DC-13 |
| AS-Interface | EN 62026-2:2013 |
| Profile | S-7.A.7 |
| Number/Type | 4 inputs for 2- or 3-wire sensors (PNP), DC |
| Ambient temperature | -25 ... 70 В°C (-13 ... 158 В°F) |
| Protection class | III |
| Relative humidity | 85 % , noncondensing |
| Diagnostic Coverage (DC) | 0 % |
| Storage temperature | -25 ... 85 В°C (-13 ... 185 В°F) |
| Current | 1 A per output |
| ID2 code | 7 |
| Rated operating current | 40 mA (without sensors) / max. 240 mA |
| Voltage | 21 ... 31 V |
| Required master specification | V3.0 |
| Switching point | according to DIN EN 61131-2 (Type 2) |
| AS-Interface specification | V3.0 |
| Mass | 150 g |
| Connection | AS-Interface and auxiliary voltage: M12 x 1 round connector sensors/actuators: M8 x 1 round connector |
| Input current | 9 mA (limited internally) |
| Altitude | 2000 m above MSL |
| Supply | from AS-Interface |
| Number/Type | 4 electronic outputs, PNP, overload and short-circuit proof |
| LED PWR/FAULT | Status display; multi-colour LED Green: normal operation Red: communication fault Flashing yellow/red: address 0 Flashing green/red: sensor supply or output overload |
| Degree of protection | IP67 / IP68 / IP69k |
| Parameter bits (programmable via AS-i) | function |
Comments
No comments yet