Pepperl+Fuchs VBG-EC-K30-DMD-S32-EV
AS-Interface Gateway/Safety Monitor
- Gateway and safety monitor in one housing
- Connection to EtherCAT
- SafeLink
- Certified up to SIL 3 according to IEC 61508 and EN 62061 and up to PLe according to EN 13849
- 2 AS-Interface networks
- Six safe electronic outputs
- Integrated data decoupling
- Dublicate addressing detection
- Earth fault detection
- AS-Interface noise detection
- Ethernet diagnostic interface
Item Number:
VBG-EC-K30-DMD-S32-EV
The price is not final. Please check with the manager!
Contact our experts
- Overview
- Comments
| Emitted interference | EN 61000-6-4:2007/A1:2011 |
| Ambient temperature | 0 ... 55 В°C (32 ... 131 В°F) |
| Safety Integrity Level (SIL) | SIL 3 |
| Interface type | RJ-45 Ethernet Diagnostic Interface |
| Rated operating current | approx. 300 mA PELV |
| PLC-Functionality | activateable |
| OK button | Mode selection traditional-graphical/confirmation |
| Physical | 2 x RJ-45 |
| AS-Interface | spring terminals, removable |
| Noise immunity | EN 61000-6-2/AC:2005 |
| Insulation voltage | 500 V |
| LED U AS-i | AS-Interface voltage; LED green |
| Button MODE | Mode selection PRJ-operation/save configuration/cursor |
| Duplicate address detection | from AS-Interface slaves |
| Functional safety | EN ISO 13849-1:2008/AC:2009, EN ISO 13849-2:2012 (up to PL e), EN 61508:2010 and EN 62061:2005+A1:2013 (up to SIL3) |
| Construction type | Low profile housing |
| ESC button | Mode selection traditional-graphical/cancel |
| LED OUT | Output circuit closed; 6 x green LEDs |
| MTTFd | 100 a |
| Button | 4 |
| Display | Illuminated graphical LC display for addressing and error messages |
| LED POWER | voltage ON; LED green |
| Response delay | < 40 ms |
| Degree of protection | IP20 |
| LED AS-i ACTIVE | AS-Interface operation normal; LED green |
| LED CONFIG ERR | configuration error; LED red |
| UL approval | An isolated source with a secondary open circuit voltage of 30 VDC with a 3 A maximum over current protection. Over current protection is not required when a Class 2 source is employed. UL mark does not provide UL certification for any functional safety rating or aspects of the device. |
| LED IN | 6 x LED green |
| Switch SET | Selection and setting of a slave address |
| Transfer rate | 10 MBit/s / 100 MBit/s , Automatic baud rate detection |
| Earth fault detection | integrated |
| AS-Interface specification | V3.0 |
| UL File Number | E223772 only from low voltage, limited energy source (SELV or PELV) or listed Class 2 source |
| Switch-on delay | < 10 s |
| LED PRG ENABLE | autom. programming; LED green |
| B10d | 2.5 E+5 |
| Ethernet | RJ-45 |
| Transfer rate | 10 MBit/s |
| Mass | 800 g |
| LED ETHERNET | EtherCAT active; LED green |
| Degree of protection | EN 60529:2000 |
| Diagnostics function | Extended function via display |
| Number/Type | 6 inputs Safety: 3 x 2 channels Or 6 standard inputs |
| Protocol | EtherCAT acc. to IEEE 802.3 |
| Safety output | 6 semiconductor outputs Output circuits: 6 PNP transistor outputs Max. contact load: 1.2 ADC-13 at 30 VDC, andSigma; = 7.2 A in total (see derating) |
| LED PRJ MODE | projecting mode active; LED yellow |
| Performance level (PL) | PL e |
| EMC monitoring | integrated |
| AS-Interface | EN 62026-2:2013 |
| Storage temperature | -25 ... 85 В°C (-13 ... 185 В°F) |
| LED AUX | ext. auxiliary voltage UAUX ; LED green |
| Rated operating voltage | 26.5 ... 31.6 V from AS-Interface; 24 V DC |
| Interface type | Chip card slot |
| Interface type | RJ-45 |
Comments
No comments yet