Pepperl+Fuchs VBG-ENX-K30-DMD-S16-EV

AS-Interface Gateway/Safety Monitor

Protocol

EtherNet/IP + MODBUS TCP/IP acc. to IEEE 802.3

supports device level ring protocol DLR

Insulation voltage

500 V

Safety Integrity Level (SIL)

SIL 3

MTTF_d

200 a

Number/Type

4 EDM/Start inputs:

EDM: Inputs for the external device monitoring circuits

Start: start inputs:

Static switching current 4 mA at 24 V, dynamic 30 mA at 24 V (T=100 andmu;s)

AS-Interface specification

V3.0

Interface type

2 x RJ-45

Ambient temperature

0 ... 55 ?°C (32 ... 131 ?°F)

ESC button

Mode selection traditional-graphical/cancel

Duplicate address detection

from AS-Interface slaves

Storage temperature

-25 ... 85 ?°C (-13 ... 185 ?°F)

Safety output

Output circuits 1 and 2: 2 potential-free contacts,

max. contact load:

3 A_DC-13 at 30 V_DC,

3 A_AC-15 at 30 V_AC

Output circuits 3 and 4: 2 PNP transistor outputs

max. contact load:

0.5 A_DC-13 at 30 V_DC

Button

4

Button MODE

Mode selection PRJ-operation/save configuration/cursor

Performance level (PL)

PL e

Transfer rate

10 MBit/s

Response delay

< 40 ms

Switch-on delay

< 10 s

AS-Interface

EN 62026-2:2013

Interface type

Ethernet: RJ-45

Diagnostic Interface

Construction type

Low profile housing , Stainless steel

LED output circuit

Output circuit closed; 4 x green LEDs

Transfer rate

10 MBit/s / 100 MBit/s , Automatic baud rate detection

OK button

Mode selection traditional-graphical/confirmation

LED PRJ MODE

projecting mode active; LED yellow

LED CONFIG ERR

configuration error; LED red

EMC monitoring

integrated

LED AUX

ext. auxiliary voltage U_AUX ; LED green

Mass

800 g

Degree of protection

IP20

Earth fault detection

integrated

B_10d

2 E+7

Rated operating voltage

26.5 ... 31.6 V from AS-Interface; Output K3 and K4 24 V _DC

LED U AS-i

AS-Interface voltage; LED green

Interface type

Chip card slot

UL approval

An isolated source with a secondary open circuit voltage of 30 V_DC with a 3 A maximum over current protection. Over current protection is not required when a Class 2 source is employed.

UL mark does not provide UL certification for any functional safety rating or aspects of the device.

LED AS-i ACTIVE

AS-Interface operation normal; LED green

Electromagnetic compatibility

EN 61000-6-2:2005, EN 61000-6-4:2007

LED EDM/Start

External device monitoring circuit inputs closed, 4x yellow LEDs

Rated operating current

300 mA from AS-Interface

LED ETHERNET

ethernet active; LED green

Degree of protection

EN 60529:2000

UL File Number

E223772 only from low voltage, limited energy source (SELV or PELV) or listed Class 2 source

LED PRG ENABLE

autom. programming; LED green

LED POWER

voltage ON; LED green

Display

Illuminated graphical LC display for addressing and error messages

PLC-Functionality

activateable

Diagnostics function

Extended function via display

Standards

EN 61000-6-2:2005, EN 61000-6-4:2007 EN 61326-3-1:2008 IEC 61508:2010 and EN 62061:2005 (up to SIL3) EN 13849:2008 (PL e)

Ethernet

RJ-45

Switch SET

Selection and setting of a slave address