Pepperl+Fuchs Products Other

• 100 V AC to 240 V AC wide-range input
• Output 24 V DC, 10 A, 240 W, 1-phase
• Housing width 39 mm
• Efficiency up to 95.2 %
• Minimal inrush current surge
• DC OK relay contact
• Suitable for Zone 2/Div. 2 mounting

• Enables easy, centralized management of a Remote Monitor via the VisuNet Control Center

• Allows you to directly connect from a VisuNet Remote Monitor to a virtualized Emerson DeltaV system

• Enables easy, centralized management of a Remote Monitor via the VisuNet Control Center

• Diffuse mode sensor for recording any print mark
• TEACH-IN, static and dynamic
• 50 micro-s response time, suitable for extremely rapid scanning processes
• 3 emitter colors: green, red and blue

EPV 2 SA 90

• Sealing: EPDM, NBR
• Maximum voltage: 250 V AC

EPV 3 SA 00

• Maximum pressure: 0.3 bar (4.4 psi)
• Vacuum: -0.08 bar (-1.2 psi)
• Maximum Flow: 8 L/H (2.1 GPM)
• Connections: G1/4, G3/8, NPT 1/8, M10 x 1
• Sealing material: EPDM, FKM

EPV 3 SA 90

• Diaphragm: Silicone rubber
• Spring: Stainless steel
• Maximum Voltage: 250V AC/DC
• Maximum current: 10 A

EPV 6000 SS 01

• Connection: G 1/4 A, internal thread
• Fluid: Liquids and gases (compatible with 316L stainless steel)
• Maximum flow rate: 30 l/min (7.925 gal/h)
• Electrical signal: 4-20 mA
• Supply voltage: 10...30 V DC
• Current consumption: max. 20 mA
• Response time: < 2 s

KFD2 CD2 EX2

• Maximum current consumption: 100 mA
• Response time: < 250 ms
• Overcurrent protection: Yes
• Short circuit protection: Yes

KFD2 GU 1

• Resolution: 0.1°C or 0.1°F
• Overload: 150% of the measurement range within 2 seconds
• Short Circuit: The output is protected against short circuits to power and ground
• Input resistance: RTD: ≤ 20 ohms
• Thermocouple: ≤ 2 MΩ
• Output resistance: ≤ 2 ohms

KFD2 STC4 2

• Connection: Screw terminals
• Mounting: On a 35 mm DIN rail according to EN 60715: 2001
• EC type conformity certificate: BAS 99 ATEX 7025 X
• Certificate: TÜV 99 ATEX 1499 X
• IECEx certificate: IECEx BAS 04.0015X IECEx CML 15.0055X

KFD2 STV4 EX2 2

• Input Impedance: Approx. 200 ohms
• Maximum input voltage: 30 V
• Reverse polarity protection: Built-in protection
• Overcurrent protection: Built-in protection

LFL2 BK U PUR5

• Rated voltage: 250 V AC / 150 V DC
• Maximum current: 1 A DC / 3 A AC
• Minimum switching current: 10 mA
• Electrical strength: 2000 V AC
• Degree of insulation resistance: > 100 MΩ
• Voltage drop across contacts: < 1 V at nominal current
• Switching time: < 10 ms

LFL2 CK U PUR3

• Maximum switching power: 750 VA
• Minimum switching current: 10 μA
• Minimum switching power: 0.25 VA
• Trigger time: < 10 ms
• Trigger time: < 10 ms
• Electrical strength: 2000 V AC
• Insulation resistance: > 100 MΩ

LFL2 CK U PUR5

• Process pressure (static pressure): ≤ 3 bar (43.5 psi) at 20°C (68°F)
• Density: ≥ 0.8 g/cm³
• Ambient temperature: 5 ... 70°C (41 ... 158°F)
• Storage temperature: -25 ... 70°C (-13 ... 158°F)
• Altitude: ≤ 2000 m above sea level
• Degree of protection: IP68
• Cable length: 5 m

LFL2 CK U PVC3

• Maximum power: 25 VA
• Minimum switching current: 10 mA
• Minimum switching voltage: 1 V
• Trigger time: ≤ 10 ms
• Trigger time: ≤ 10 ms

LFL2 CK U PVC5

• Degree of protection: IP65/IP67
• Operating temperature range: From -20°C to +70°C
• Installation: Vertical or horizontal

M LB 5000

• Nominal current: Up to 2 A
• Breakdown voltage: Up to 1 kV
• Discharge energy: Up to 10 J
• Input resistance: 10 ohms
• Output resistance: 1 Ohm
• Insulation resistance: > 10 GΩ

MB F95M Z1 V3

• Trigger time: ≤ 2 ms
• Trigger time: ≤ 5 ms
• Reverse current: ≤ 1 mA
• Breakdown voltage: ≥ 250 V DC. current
• Electrical insulation resistance: ≥ 100 MΩ

MB80 12GM50 E0

• Connection type: PUR cable, 2 m (black)
• Core cross-section: 0.14 mm2
• Body material: brass, nickel-plated
• Sensitive surface: PBT
• Degree of protection: IP67
• Connections: BN, L+, L-, BK, BU

MB80 12GM50 E2

• Power consumption: ≤ 1.5 W
• Supply voltage: 10 ... 30 V DC
• Nominal current: ≤ 100 mA
• Maximum switching voltage: 250 V DC / 100 V AC
• Maximum switching current: 2 A
• Trigger time: ≤ 0.5 ms
• Reset time: ≤ 0.5 ms

OJ 500 M1K E23

• Body material: stainless steel
• Degree of protection: IP67
• Operating temperature: -25...70°C

PB D02 008 6

• Button pressing force: 2.5 N
• Button stroke: 4 mm
• Button life: 1 million cycles
• Installation: panel, on a DIN rail

PG11 CORD GRIP

• Body: nickel-plated brass
• Sealing: EPDM
• Nut: nickel-plated brass

R2 SP IC4

• Relative humidity: 0...95% (without condensation)
• Body material: polycarbonate
• Trigger voltage: 10.5 V DC

SJ5 K E2 Y33968

• Current consumption: ≤ 10 mA
• Residual current: ≤ 2 mA
• Reverse polarity protection: Yes
• Short circuit protection: Yes
• Trigger time: ≤ 0.2 ms
• Reset time: ≤ 0.1 ms
• Hysteresis: ≤ 2%
• Load capacity: 100 mA

TB RS DO16 AKB 204061

• Output type: PNP
• Maximum load voltage: 30 V
• Minimum reset voltage: 0.8V
• Output delay time: < 1ms
• Output reset time: < 1ms

TC1200 1000

• Degree of protection: IP64
• Connection: Fixed cable with 9-pin Sub-D connector
• Material: Body - ABS plastic

VAA 2E1A F85A S V1

• Trigger force: max. 15 N
• Trigger stroke: 5 mm
• Reset force: max. 10 N
• Reset stroke: 5 mm