Pilz PSEN Safety switches
PSEN cs2.2p / PSEN cs2.1 1 Unit
- Operating temperature range: -25°C - 70°C
- Standard storage temperature: -40°C - 85°C
- Degree of protection: IP67
- Drive type: PSEN cs2.1
- The possibility of close installation: Yes
- Connection type: M12, 8-pin connector
PSEN cs1.19n 1 switch
- Installation: wall/DIN-rail
- Working position: any
- Tilt range: ± 15°
- Certificates: TÜV, CE, CCC
PSEN cs3.1a /PSEN cs3.1 1unit
- Trigger distance: 10 mm (max.)
- Change in operating distance with temperature: ±0.01 mm/°C
- Trigger time: < 20 ms
- Reset time: < 100ms
- Switching frequency: max. 1000 Hz
- Reliability: > 10^9 actuation cycles
PSEN cs3.1b /PSEN cs3.1 1unit
- Cable bending radius: 5 x Ø
- Drive type: PSEN cs3.1
- The possibility of close installation: Yes
- Connection type: 10 m cable
- Cable lines: Li9Y11Y 8 x 0.14 mm²
- Body material: PBT
PSEN cs3.1 M12/8-1.5m/PSEN cs3.1 1unit
- Operating voltage range: 20.4 V DC - 28.8 V DC
- Maximum current consumption: 150 mA
- Trigger time: < 10 ms
- Reset time: < 10 ms
- Switching frequency: < 10 Hz
- Electrical strength: 2000 V AC/DC
- Insulation resistance: > 20 MΩ
PSEN cs3.1b 1 switch
- Current consumption: ≤ 100 mA
- Output current: ≤ 2 A
- Output activation time: ≤ 10 ms
- Output reset time: ≤ 10ms
PSEN cs3.1 M12/8-1.5m 1switch
- Supply voltage: 24 V DC (+/- 10%)
- Current consumption: max. 100 mA
- Output: 2x OSSD (Safety Solid State Output)
- Switching range: depending on the drive, serial connection
- Activation time: max. 10 ms
- Reset time: max. 5 ms
- Short circuit protection: yes
- Reverse polarity protection: yes
PSEN cs4.1n / PSEN cs4.1 1 Unit
- Overvoltage category: III
- Degree of contamination: Clean
- Creep: 3
- Type of protection, housing: IP67
- Bending radius (when laying): K15 x Ø
- Drive: PSEN cs4.1
- The ability to install the sensor close to each other: Yes (please pay attention to the installation instructions)
- Connection type: M12, 5-pin socket
PSEN cs4.1 M12/8-0.15m/PSEN cs4.1 1Unit
- Maximum current: 2 A
- Switching voltage: 24 V DC
- Switching current: 2 A
- Trigger time: < 10 ms
- Reset time: < 10 ms
- Switching frequency: max. 1000 Hz
- Electrical strength: 2500 V (RMS)
PSEN cs4.1n 1switch
- Body material: PBT
- Impact resistance: IK07
- Vibration: 10 g, 10 - 500 Hz
- Degree of pollution: 3
- Installation: Wall or panel
- Fastening type: 2 x M4
PSEN cs4.1 M12/8-0.15m 1switch
- Type of protection, housing: IP67
- Bending radius (when laying): K15 x Ø
- The ability to install the sensor close to each other: Yes (please pay attention to the installation instructions)
- Connection type: M12, 8-pin socket
- Cable lines: Li9Y11Y 8 x 0.14 mm2
- Body material: PBT
PSEN cs4.1p 1switch
- Trigger time: < 10 ms
- Reset time: < 10 ms
- Supply voltage: 24 V DC (+/- 10%)
- Power consumption: 1 W
- Input current: 40 mA
- Output current: 200 mA
- OSSD output voltage: 18 V DC
- OSSD output current: 200 mA
- OSSD delay time: 0.5ms
- OSSD reset time: 10ms
PSEN cs4.2n / PSEN cs4.1 1 Unit
- Type of protection, housing: IP67
- Bending radius (when laying): K15 x Ø
- Drive type 1: PSEN cs4.1
- The ability to install the sensor close to each other: Yes (please pay attention to the installation instructions)
- Connection type: M12, 5-pin socket
- Cable lines: Li9Y11Y 8 x 0.14 mm2
- Body material: PBT
PSEN cs4.2n 1switch
- Type of protection, housing: IP67
- Bending radius (when laying): K15 x Ø
- The sensor can be installed close to: Yes, Montagehinweis beachten
- Connection type: M12, 5-pin socket
- Cable lines: Li9Y11Y 8 x 0.14 mm2
- Upper body material: PBT
PSEN cs4.2 M12/8-0.15m 1switch
- Cable bending radius: 15 x cable Ø
- Close fitting: Yes
- Connection type: M12, 8-pin socket
- Cable: Li9Y11Y 8 x 0.14 mm2
- Body material: PBT
PSEN cs4.2p 1switch
- Trigger force: max. 15 N
- Body: Aluminum
- Contact group: Gold-plated brass
- Sealing: EPDM
PSEN cs3.19n 1 switch
- Bending radius (when laying): K15 x Ø
- Drive type: PSEN cs3.19
- Possible to install the sensor in close proximity: Yes, Montagehinweis beachten
- Connection type: M12, 5-pin socket
- Cable lines: Li9Y11Y 8 x 0.14 mm2
- Body material: PBT
PSEN cs5.11 M12/8/PSEN cs5.11 M12 1unit
- Trigger range: 11 mm (with the activator in the square position)
- Travel margin: 8 mm (Sao)
- Residual stroke: 20 mm (Sar)
- Actuation force: < 5 N
- Trigger frequency: up to 50 Hz
- Vibration level: 10 g at 10 - 500 Hz
- Degree of impact: 30 g at 11 ms
PSEN me1M / 1AR
- Body material: Metal (usually stainless steel)
- Installation: On the surface
- Temperature range: Depends on the modification, but usually from -25°C to +70°C
- Vibration resistance: High
- Noise: Low level
PSEN ml b 1.1 unit
- Bend radius (when laying) K1: 5 x Ø
- Escape release available: No
- Type: 1 actuator PSEN ml 1.1
- Connection type: M12, 8-pin male
PSEN ml b 1.1 switch
- Number of OSSD outputs 2
- Number of sig. outputs 1
- Potential isolation S/C O No
- S/C output short circuit proof Yes
- Utilisation cat. to EN 60947-1 DC-13
PSEN ml b 2.1 unit
- Operating Temperature: 0 to 60°C
- Storage Temperature: According to EN 60068-2-1/-2
- Humidity: 93% relative humidity at 40°C
- EMC: Compliant with EN 55011, EN 60947-5-3, and EN 61326-3-1
PSEN ml b 2.1 switch
- Operating temperature: 0 to 60°C
- Storage temperature: According to EN 60068-2-1/-2
- Humidity: 93% r.h. at 40°C
- Vibration and shock: Compliant with EN 60068-2-6, 130g shock
PSEN ml s 1.1 unit
- Principle of operation: Transponder
- ISO 14119 Coding Level: Low
- Classification according to EN 60947-5-3: PDDB
- Transponder encoding type: Encoded
- Reset Type: Power Reset
- Possibility of serial connection: Yes
PSEN ml escape release
- Built-in position sensor
- Ability to connect to external devices
- Diagnostic functions
PSEN sl-0.5p 2.1 / PSEN sl-0.5 1unit
- Electrical connection: 8-pin M12 connector
- Holding force: 500 N
- Material of the actuator: Stainless steel
- Degree of protection of the actuator: IP67
- Number of outputs: 2
PSEN sl-0.5p 2.2 / PSEN sl-0.5 1unit
- Product type: Magnetic safety gate system
- Assured release distance: 8.0 mm
- Certifications: CE, cULus Listed, EAC (Eurasian), TÜV
- Dimensions: 45 mm x 122 mm x 44 mm
PSEN sl-0.5n 1.1 / PSEN sl-0.5 1unit
- Inputs: 1
- Outputs: 2 OSSD outputs
- Short circuit proof: Yes
- Utilization category: DC-12
- Ambient temperature: -25 to 55 °C
- Storage temperature: -25 to 70 °C
PSEN sl-0.5p 2.1 1switch
- S/C output short circuit proof: Yes
- Utilisation cat. to EN 60947-1: DC-12
- Ambient temperature standard: EN 60068-2-14
- Ambient temperature: -25 - 55 °C
- Storage temperature standard: EN 60068-2-1/-2
- Climatic suitability standard: EN 60068-2-78
- Humidity rating: 93 % r. h. at 40 °C
PSEN sl-0.5p 1.1 / PSEN sl-0.5fm 1unit
- Protection type: IP67
- Holding force: 500 N
- Max. vertical offset: 5 mm
- Max. angular offset: 2.5 degrees
- Ambient temperature: -25 to 55 °C
- Humidity: 93% RH at 40 °C