Pepperl+Fuchs OMT600-R200-IEP-IO-V31-L Distance sensor
Item Number: OMT600-R200-IEP-IO-V31-L
- Medium design with versatile mounting options
- Space-saving distance sensors in small standardized design
- Multi Pixel Technology (MPT) - exact and precise signal evaluation
- IO-link interface for service and process data
- Analog output 4 ... 20 mA
- Overview
- Datasheet
- Alternative numbers
- Comments
| Mass | approx. 35 g |
| Angle deviation | max. +/- 1.5 В° |
| Output type | 1 current output: 4 ... 20 mA |
| Diameter of the light spot | approx. 3 mm at a distance of 600 mm |
| Signal output | 1 push-pull output , 1 analog output , short-circuit-proof, reverse polarity protection, surge-proof |
| Storage temperature | -40 ... 70 В°C (-40 ... 158 В°F) |
| Warm up time | 5 min |
| Compatible master port type | A |
| Ambient light limit | EN 60947-5-2 : 15000 Lux |
| Response time | 2 ms |
| Linearity error | 0.75 % |
| Light source | laser diode |
| MTTFd | 470 a |
| Ambient temperature | 10 ... 50 В°C (50 ... 122 В°F) |
| Min. cycle time | 3 ms |
| Degree of protection | IP67 / IP69 / IP69K |
| CCC approval | CCC approval / marking not required for products rated ≤36 V |
| Interface type | IO-Link ( via C/Q = pin 4 ) |
| Control elements | 5-step rotary switch for operating modes selection |
| Function indicator | LED yellow: constantly on - switch output active constantly off - switch output inactive |
| IO-Link Revision | 1.1 |
| Device ID | 0x111908 (1120520) |
| Voltage drop | ≤ 1.5 V DC |
| Housing depth | 41.7 mm |
| Reference target | standard white, 100 mm x 100 mm |
| Usage category | DC-12 and DC-13 |
| Mission Time (TM) | 20 a |
| Protection class | III |
| FDA approval | IEC 60825-1:2014 Complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007 |
| Connection | M8 x 1 connector, 4-pin |
| Communication interface | IEC 61131-9 |
| Switching type | The default setting is: C/Q - Pin4: NPN normally open, PNP normally closed, IO-Link I—Pin2: analog output 4...20 mA |
| Control elements | Teach-In key |
| Temperature drift | 0.05 %/K |
| Transfer rate | COM 2 (38.4 kBaud) |
| Operation indicator | LED green: constantly on - power on flashing (4Hz) - short circuit flashing with short break (1 Hz) - IO-Link mode |
| Resolution | 0.1 mm |
| UL approval | E87056 , cULus Listed , class 2 power supply , type rating 1 |
| Load resistor | > 1 kΩ voltage output ; ≤ 470 Ω current output |
| Housing width | 15 mm |
| Switching voltage | max. 30 V DC |
| Housing height | 50.6 mm |
| Switching current | max. 100 mA , resistive load |
| No-load supply current | < 18 mA at 24 V supply voltage |
| Operating voltage | 18 ... 30 V DC |
| Product standard | EN 60947-5-2 |
| Diagnostic Coverage (DC) | 0 % |
| Measurement range | 100 ... 600 mm |
| Process data width | Process data input 4 byte Process data output 2 bits |
| Ripple | max. 10 % |
| Laser safety | EN 60825-1:2014 |
| Device profile | Identification and diagnosis Smart Sensor type 0/type 3.3 |
| Light type | modulated visible red light |
| Angle of divergence | approx. 0.3 В° |
| SIO mode support | yes |
| Repeat accuracy | < 1 % |
Comments
No comments yet