Pepperl+Fuchs Explosion Protection
Choose a subcategory:
Show all categories
- 4-channel
- Inputs Ex ia, Outputs Ex ia
- Installation in suitable enclosures in Zone 1
- Module can be exchanged under voltage (hot swap)
- Analog input, digital input,
analog output, digital output - Supply circuit 21.5 V (4 mA)
- HART communication via field bus or service bus
- Simulation mode for service operations (forcing)
- Line fault detection (LFD): one LED per channel
- Permanently self-monitoring
- Interface between the I/O modules and the PCS/PLC
- Com unit for 80 analog or 184 digital channels
- Communication via PROFIBUS DP
- Installation in suitable enclosures in Zone 1
- Module can be exchanged under voltage (hot swap)
- HART communication via PROFIBUS DP V1 or service bus
- Configuration via GSD parameters from the control system
- Non-volatile memory for configuration and parameter settings
- Self configuration in redundant systems
- Permanently self-monitoring
- Outputs drive to safe state in case of failures
- Interface between the I/O modules and the PCS/PLC
- Com unit for 80 analog or 184 digital channels
- Communication via PROFIBUS DP
- Installation in suitable enclosures in Zone 1
- Module can be exchanged under voltage (hot swap)
- HART communication via PROFIBUS DP V1 or service bus
- Configuration via GSD parameters from the control system
- Non-volatile memory for configuration and parameter settings
- Self configuration in redundant systems
- Permanently self-monitoring
- Outputs drive to safe state in case of failures
- Interface between the I/O modules and the PCS/PLC
- Com unit for 80 analog or 184 digital channels
- Communication via MODBUS RTU
- Installation in suitable enclosures in Zone 1
- Module can be exchanged under voltage (hot swap)
- HART communication via service bus
- Configuration via FDT 1.2 DTM
- Non-volatile memory for configuration and parameter settings
- Self configuration in redundant systems
- Permanently self-monitoring
- Outputs drive to safe state in case of failures
- Interface between the I/O modules and the PCS/PLC
- Com unit for 80 analog or 184 digital channels
- Communication via PROFIBUS DP
- Module can be exchanged under voltage (hot swap)
- HART communication via PROFIBUS DP V1 or service bus
- Installation in suitable enclosures in Zone 1
- Configuration via FDT 1.2 DTM
- Configuration in run (CiR) for any PCS
- Non-volatile memory for configuration and parameter settings
- Self configuration in redundant systems
- Permanently self-monitoring
- Outputs drive to safe state in case of failures
- Interface between the I/O modules and the PCS/PLC
- Com unit for 80 analog or 184 digital channels
- Communication via PROFIBUS DP
- Installation in suitable enclosures in Zone 1
- HART communication via PROFIBUS DP V1 or service bus
- Configuration via FDT 1.2 DTM
- Configuration in run (CiR) for any PCS
- Non-volatile memory for configuration and parameter settings
- Self configuration in redundant systems
- Permanently self-monitoring
- Outputs drive to safe state in case of failures
- Power supply for 95 - 230 V AC
- Suitable for the supply of FOL, field products (analyzers, level meters etc.)
- Installation in suitable enclosures in Zone 1
- Module can be exchanged under voltage (hot swap)
- Use two power supplies for redundancy
- Galvanic isolation to mains
- Power supply for 24 V DC
- Suitable for the supply of 24 I/O modules and 1 bus coupler
- Installation in suitable enclosures in Zone 1
- Module can be exchanged under voltage (hot swap)
- Power supply for 24 V DC
- Installation in suitable enclosures in Zone 1
- Module can be exchanged under voltage (hot swap)
- Multi range power supply 90 ... 253 V AC
- Suitable for the supply of 24 I/O modules and 1 bus coupler
- Use two power supplies for redundancy
- Installation in suitable enclosures in Zone 1
- Module can be exchanged under voltage (hot swap)
Remote I/O Unit
Remote I/O Unit
Remote I/O Unit
Remote I/O Unit
Remote I/O Unit
Remote I/O Unit
Remote I/O Unit
Remote I/O Unit
- For 20 analog or 40 digital channels
- Sensors in Zone 0/Div. 1 (depending on module assembly)
- Installation in Zone 2, Div. 2 or safe area
- HART communication via service bus
- For FOUNDATION Fieldbus H1
- Configured via the process control system
- Non-volatile memory for configuration and parameter settings
- Quick communication set-up
- Permanently self-monitoring
- Outputs drive to safe state in case of failures
- Module can be exchanged under voltage
- 16-channel
- Connection board for K-System HART Multiplexer
- Interface for parallel connections
- Connection via spring terminals
- System board for Triconex
- HART Termination Board (ETP) for Tricon v10 AI module
- For 16-channel AI cards 3700, 3700A, 3703E and 3721
- 16-channel
- Field side: screw terminals, green
- Control side: ELCO socket, 56-pin
- System board for Triconex
- HART Termination Board (ETP) for Tricon AO module
- For 8-channel AO card 3805E
- 8-channel
- Field side: screw terminals, green
- Control side: ELCO socket, 56-pin
- 1-channel
- Field mount module
- frac12- NPT thread
- Stainless steel housing
- Max. surge current (8/20 micro-s) 20 kA
- 500 V isolation from earth
- Suitable for hazardous area
- For any PROFIBUS interface, e.g. Remote I/O, valves, drives, inverters, motors, controllers etc.
- Full galvanic isolation between field and control room
- No sparks capable of ignition or hot surfaces due to low light energies
- Automatic baud rate detection
- Star, ring, or line topology selectable
- Bridging of great distances while maintaining high transmission rates
- 1-channel
- Field mount module
- M20 x 1.5 thread
- Stainless steel housing
- Max. surge current (8/20 micro-s) 20 kA
- 500 V isolation from earth
- Suitable for hazardous area