Pepperl+Fuchs

• Suitable for Zone 1 21 operation, ATEX/IECE certification
• Manifold combines the digital valve for purging and the needle valve for pressurization in one housing
• Suitable for steel or plastic tubing
• Mounting hardware, pneumatic fittings and tubing included

Incremental rotary encoder 

• Ex e and Ex tb certified
• Suitable for operation in Zone 1, Zone 2, Zone 21 and Zone 22
• Stainless Steel
• Thread NPT 1/2''
• Seal silicone
• Packaging unit: 35 pieces, with accessories

• Diffuse mode sensor for recording any print mark
• TEACH-IN, static and dynamic
• 50 micro-s response time, suitable for extremely rapid scanning processes
• 3 emitter colors: green, red and blue

ENA58IL S10CA5 1213B17 ABP

• Body: AISI 303 stainless steel
• Shaft: AISI 303 stainless steel
• Bearings: Ball bearings
• Sealing: EPDM

ENI58IL S10CA5 1024UD1 RC1

• Shaft torque: Max. 1.5 Nm
• Permissible radial load: Max. 100 N
• Permissible axial load: Max. 50 N
• Impact resistance: Up to 50 g
• Vibration resistance: Up to 10 g (peak-peak)

EPV 2 SA 90

• Sealing: EPDM, NBR
• Maximum voltage: 250 V AC

EPV 3 SA 00

• Maximum pressure: 0.3 bar (4.4 psi)
• Vacuum: -0.08 bar (-1.2 psi)
• Maximum Flow: 8 L/H (2.1 GPM)
• Connections: G1/4, G3/8, NPT 1/8, M10 x 1
• Sealing material: EPDM, FKM

EPV 3 SA 90

• Diaphragm: Silicone rubber
• Spring: Stainless steel
• Maximum Voltage: 250V AC/DC
• Maximum current: 10 A

EPV 6000 SS 01

• Connection: G 1/4 A, internal thread
• Fluid: Liquids and gases (compatible with 316L stainless steel)
• Maximum flow rate: 30 l/min (7.925 gal/h)
• Electrical signal: 4-20 mA
• Supply voltage: 10...30 V DC
• Current consumption: max. 20 mA
• Response time: < 2 s

Segment Protector F2-SP-IC* F2-SP-IC08.1.03.03.00

Connection plate for HART multiplexer in K system
16-way version

FL2B 2J6 E

• LED status indicator
• Reverse polarity protection
• CE, cULus, EAC certification

FL2B 4J6 E

• Switching voltage: ≤ 250 V DC
• Maximum switching current: ≤ 2 A
• Residual current: ≤ 10 μA
• Trigger time: ≤ 0.2 ms
• Reset time: ≤ 0.1 ms
• Reverse polarity protection: yes
• Short circuit protection: yes

• Output: 28 ... 30 V/500 mA
• High-power trunk for high device count and long cable lengths
• With galvanic isolation
• Installation in Zone 2/Class I, Div. 2
• For FOUNDATION Fieldbus H1 and PROFIBUS PA
• Highest efficiency, lowest heat dissipation for highest packing density
• Hot swappable in redundant configuration
• Module exchange without tools during operation

This item is out of production!

• 1-channel isolated barrier
• 24 V DC supply (bus powered)
• 2-wire SMART transmitter
• Output for 4 mA ... 20 mA or 1 V ... 5 V
• Sink or source mode
• Line fault detection (LFD)
• Up to SIL 3 acc. to IEC 61508

HPV D13

• Current consumption: < 10 mA
• Reverse polarity protection: Yes
• Short circuit protection: Yes
• On/off delay time: < 2ms
• Operating temperature: -20°C...+70°C

KFD2 CD2 EX1

• Marking: space for marking on the front panel
• Electromagnetic compatibility: Directive 2014/30/EU: EN 61326-1:2013 (industrial premises)
• Degree of protection: IEC 60529:2001
• Protection against electric shock: UL 61010-1:2004
• Ambient temperature: -20...60 °C (-4...140 °F)

KFD2 CD2 EX2

• Maximum current consumption: 100 mA
• Response time: < 250 ms
• Overcurrent protection: Yes
• Short circuit protection: Yes

• 1-channel isolated barrier
• 24 V DC supply (Power Rail)
• Level sensing input
• Adjustable range 1 k Omega- ... 150 k Omega-
• Relay contact output
• Fault relay contact output
• Adjustable time delay up to 10 s
• Minimum/maximum control
• Line fault detection (LFD)

KFD2 GU 1

• Resolution: 0.1°C or 0.1°F
• Overload: 150% of the measurement range within 2 seconds
• Short Circuit: The output is protected against short circuits to power and ground
• Input resistance: RTD: ≤ 20 ohms
• Thermocouple: ≤ 2 MΩ
• Output resistance: ≤ 2 ohms

• 2-channel signal conditioner
• 24 V DC supply (Power Rail)
• Current output up to 700 Omega- load
• HART I/P and valve positioner
• Line fault detection (LFD)
• Accuracy 0.05 %
• Terminal blocks with test sockets
• Up to SIL 2 acc. to IEC 61508

• 2-channel isolated barrier
• 24 V DC supply (Power Rail)
• Dry contact or NAMUR inputs
• Usable as signal splitter (1 input and 2 outputs)
• 2 x 2 relay contact outputs with AND logic
• Line fault detection (LFD)
• Reversible mode of operation
• Up to SIL 2 acc. to IEC 61508

KFD2 STC4 2

• Connection: Screw terminals
• Mounting: On a 35 mm DIN rail according to EN 60715: 2001
• EC type conformity certificate: BAS 99 ATEX 7025 X
• Certificate: TÜV 99 ATEX 1499 X
• IECEx certificate: IECEx BAS 04.0015X IECEx CML 15.0055X

• 2-channel isolated barrier
• 24 V DC supply (Power Rail)
• Input 2-wire SMART transmitters
• Output 0/4 mA ... 20 mA current sink
• Terminal blocks with test sockets
• Up to SIL 2 acc. to IEC 61508

KFD2 STV4 EX2 2

• Input Impedance: Approx. 200 ohms
• Maximum input voltage: 30 V
• Reverse polarity protection: Built-in protection
• Overcurrent protection: Built-in protection

LFL2 BK U PUR5

• Rated voltage: 250 V AC / 150 V DC
• Maximum current: 1 A DC / 3 A AC
• Minimum switching current: 10 mA
• Electrical strength: 2000 V AC
• Degree of insulation resistance: > 100 MΩ
• Voltage drop across contacts: < 1 V at nominal current
• Switching time: < 10 ms

LFL2 CK U PUR3

• Maximum switching power: 750 VA
• Minimum switching current: 10 μA
• Minimum switching power: 0.25 VA
• Trigger time: < 10 ms
• Trigger time: < 10 ms
• Electrical strength: 2000 V AC
• Insulation resistance: > 100 MΩ

LFL2 CK U PUR5

• Process pressure (static pressure): ≤ 3 bar (43.5 psi) at 20°C (68°F)
• Density: ≥ 0.8 g/cm³
• Ambient temperature: 5 ... 70°C (41 ... 158°F)
• Storage temperature: -25 ... 70°C (-13 ... 158°F)
• Altitude: ≤ 2000 m above sea level
• Degree of protection: IP68
• Cable length: 5 m